Genie garage door opener parts from 1st Garage Door Openers Inc.

Genie Garage Door Openers

Garage Door Opener Parts for Genie Garage Door Openers Intellicode and OverHead Door CodeDodger Garage Doors, Garage Keypads, Garage Remotes

1st Garage Door Openers, Inc.
 BBB Business Review

 

  Genie-Garage-Door-Openers on facebook

GIT90-1 Genie Garage Door Opener Intellicode One Button Remote Control Transmitter

REMOTES

GWKIC Genie Garage Door Opener Intellicode and Overhead Door CodeDodger Keyless Entry System
KEYLESS ENTRY

20414R Genie Garage Door Openers Screw Drive Carriage Assembly
REPAIR PARTS
 
Genie Garage Door Openers Safety Beam Sensor Kit STBK

SAFETY SENSORS

 

All Online Ordering
Is Safe and Secure

 

 

 

 

 

               

Digital Wireless Keypad With  Intellicode  NEW STYLE

GWKIC,  GWKP,  ACSD1G

INSTALLATION AND PROGRAMMING INSTRUCTIONS

PROGRAM KEYPAD BEFORE MOUNTING

  1. INSTALLATION INSTRUCTIONS         
  2. BASIC PROGRAMMING         
  3. PROGRAMMING MULTIPLE DOOR OPERATORS
  4. ENHANCED PROGRAMMING

Features

  • Controls up to three Intellicode garage door openers.

  • Simple to Program and Install.

  • Pin Codes can be up to 8 characters.

  • Low Battery Power Indicator.

  • Stays programmed during battery change.

  • Temporary PIN for special purpose access.

*************   WARNING   *************

            Moving Door can cause serious injury or death.

·         DO NOT install transmitter unless the door operator’s safety reverse works as required by the door operator’s manual.

·         Wall control must be mounted in sight of door, at least 5 feet above floor and clear of moving door parts.

·         Keep people clear of opening while door is moving.

·         DO NOT allow children to play with the transmitter or door operator.

If safety reverse does not work properly:

·         Close door then disconnect operator using the manual release handle.

·         DO NOT use transmitter or door operator.

·         Refer to Door and Door Operators Owner’s Manuals before attempting any repairs.

_________________________________________________

 

            Electrical Shock can cause serious injury or death.

·         Power cord must be unplugged before attaching any wires,

·         Be sure wire ends do not touch each other or other terminals.

If you have questions or if you need a manual, contact the distributor or manufacturer of the operator.

******************************************************************************************************************************

1. INSTALLATION INSTRUCTIONS

    NOTE: For convenience in programming you may wish to install Wireless Keypad after Basic Programming of Wireless Keypad and Garage Door Operator(s) is completed.

·     Mount keypad (mounting screws located inside battery compartment.

·     Slide off battery cover and remove battery.

·      Mark two holes by tapping a small nail through screw holes on keypad. Drill 1/16’ pilot holes then fasten with #6 screws enclosed. Replace Keypad cover.

·      Replace battery and slide battery cover back into place.

           Section 1 - Programming for One Door Opener

            Step 1 - Activate programming mode.

  • Press in order 3, 5, 7, PROG button - Red LED blinks - once per second
  • Enter you PIN ( 3 to 8 characters)
  • Press PROG button - Red LED blinks - twice per second and turns off.

            Step 2 - Programming One Door Openers

  • Find the Learn Code Button and Learn Code Indictor LED on your door opener.  (This can be found where you see the antenna wire hanging from the motor head (you may have to take the lens cover off). If antenna wire is not hanging from motor head then you have an external receiver which is a black box approx. 6" x 2" mounted somewhere in the garage with a antenna wire hanging from it (pop off cover to find Learn Code Button).
  • Press the Learn Code Button - Learn Code Indictor LED (on opener) will blink.
  • Enter your PIN and Press the up/down arrow button on keypad - Learn Code Indicator LED stays on.
  • Press the up/down arrow button again - Learn Code Indicator LED turns off - Wait until Keypad Backlight turns off approximately 30 seconds.

            Step 3 - Operating One Door Opener

  • To operate the Garage Door - Enter your PIN - Press the up/down button.

NOTE:  If the Door does not move, check the red LED on the keypad.  If the LED is blinking rapidly, the PIN was entered incorrectly.  After the LED stops blinking, re-enter your PIN and try again.

Any Keypad button will control the door for 30 seconds after the door starts moving.

Rapid blinking of the red LED indicates an error.  After a few seconds the LED will turn off.  Start over.

           Section 2 - Programming for 2 or 3  Door Openers

            Step 1 - Activate programming mode.

  • Press in order 3, 5, 7, PROG button - Red LED blinks - once per second
  • Enter you PIN ( 3 to 8 characters)
  • Press PROG button - Red LED blinks - twice per second and turns off.

            Step 2 - Programming for Multiple Door Openers

  • All Door Openers Will Use THE SAME PIN
  • Enter your PIN and pres PROG button - Red LED blinks - once per second.
  • Press PROG button again - Red LED blinks - twice per second
  • Press the number of Doors (total) you wish to control - press number 2 or 3
  • Press PROG button - Red LED blinks several times and turns off

            Step 3 -  Programming Door Openers

  • Decide which Door will be Door #1, #2 and #3
  • Find the Learn Code Button and Learn Code Indictor LED on your door opener.  (This can be found where you see the antenna wire hanging from the motor head (you may have to take the lens cover off). If antenna wire is not hanging from motor head then you have an external receiver which is a black box approx. 6" x 2" mounted somewhere in the garage with a antenna wire hanging from it (pop off cover to find Learn Code Button).
  • Press the Learn Code Button - Learn Code Indictor LED (on opener) will blink.
  • Enter your PIN and Press the up/down arrow button on keypad - Learn Code Indicator LED stays on.
  • Press the number you have picked for this Door Opener button numbered 1, 2 or 3 - Learn Code Indicator LED stays on.
  • Press the up/down button - Learn Indicator LED turns off.

Repeat Step 3  for each Door Opener.  Each Door Opener must be programmed to receive the signal from the Wireless Keypad.

  • Press the up/down arrow button again - Learn Code Indicator LED turns off - Wait until Keypad Backlight turns off approximately 30 seconds.

            Step 4 - Operating 2 or 3 Door Openers

  • To operate the Garage Door - Enter your PIN - Press the up/down button - Press Door Opener Number 1, 2 or 3.

           Section 3 - Additional Operations

            FORGOT YOUR PIN or CHANGING YOUR PIN

  • Erase old PIN - Press and hold in order - PROG button, number 6 button and up/down button - Red LED will blink once and turn off.

  • Release all buttons

  • Programming Door Openers - Return to Programming in Section 1 or Section 2

            Using a Temporary PIN

  • A temporary PIN allows temporary access to your home by repair persons, meter readers, etc, if you so desire.

  • Enter your PIN - Press PROG button, PROG button, PROG button (3 times)

  • Enter the temporary PIN ( 3 to 8 characters) - press PROG button

   NOTE:  DO NOT reprogram the door openers - Temporary PIN remains active until the next time your normal PIN is entered.

          

Home | Remotes | Keyless Entry | Secoders & Control Boards | Repair Parts | Safety Sensors | Wall Controls Accessories | Door Lubricant | Genie Shop Vacs | Shipping/Returns | About Us | Customer Assistance | Coding Instructions | Fax or Check Orders | Site Map |

genie-garage-door-openers.com - Owned by 1st Garage Door Openers, Inc., an independent family owned and operated business serving the Garage Door and Garage Door Opener Industry since 1981.  Providing excellent customer service and assistance for over 25 years. We are a discount reseller of  garage door opener remotes, repair parts, keyless entry and gate operator controls for your home, business, or gated community.   We carry parts for the following garage door openers Lift-Master, Chamberlain, Sears Craftsman, Access Master, Sears Best Craftsman, Sears Automatic Door Opener, Master Mechanic, Security +, Formula 1, Garage Master, Billion Code, LiftMaster Professional, Estate Series, Premium Series, Contractor Series, Power Driver, Whisper Drive, Genie, Alliance, Norelco, Blue-Max, Lift-A-Door, Pro Max, Aladdin, Hercules, Stealth, Excelerator, Intellicode, Genie Pro, OverDrive, Python 2, Signature, Phantom, Legacy, Medallion, CodeDodger, Overhead Door, Genie Shop Vac, Stanley, Vemco, Quiet Glide, SecureCode, Lightmaker, Innovative Products, Whistler, U-Install, Popular Mechanics, Allister, Allstar, Pulsar, MVP, Challenger, GTO, All-O-Matic, Electrolift, Westinghouse, AM/11, Linear, Access Pro, Moore-O-Matic, MegaCode, Delta 3, MultiCode, Heddolf, ESP Micom, Intercontinental Dynamics, Crusader, Wayne Dalton, iDrive, Door Master, Quantum, Classic Drive, Tec Key, Martec, Monarch, Telectron and other garage door openers, and gate operators. Brand names of Garage Door openers are registered trade names of the respective entities and are only used for reference.


Copyright © 2017 Genie Garage Door Openers

       

1st Garage Door Openers Inc.
Copyright © 2017 All Rights Reserved. No part of this site can be reproduced in any form or by any means, photocopying, electronic, mechanical, or otherwise, without the prior written permission of 1st Garage Door Openers Inc., Mesa, AZ  85203